From FreeCAD to pattern
The shape of this bag is mainly to see how to design a bag so that curved panels fit to each other. In my understanding this is the magic of pattern design. Fabric, at least techincal fabric, does not stretch and thus all panels have to be developable surfaces. This means, they can be unrolled and lie flat.
Developable surfaces
A surface is developable when its Gaussian curvature is zero everywhere. In practice that means it is bent in only one direction at each point, like a sheet of paper or sheet metal. Cylinders, cones and "tangent developables" are the basic families. A sphere is not developable.
Two curves are not enough
FreeCAD provides a method to join two curves to a surface. This is like taking a ruler and sweeping it along both curves. It is called "ruled surface", who would have thought. In general the output of this is not a developable surface. The two curves have to match some rules. One possible rule and the one used in this bag is to have the surface being part of a cone.
Make one curve a scaled copy of the other, scaled about a single point (the apex). Then all straight lines between matching points meet in that apex, and every cone is developable.
The basic shape of the bag will be symmetric along the x and y axis, so the design is done on a quarter of the bag. The middle of the belly will always have a seam, because that is where two cone segments will meet end to end.

Why ellipses give the belly
For the boundary curves I used ellipse arcs. Two ellipse arcs joined by a ruled surface form an elliptic cone when the ellipses are similar and similarly placed:
- same ratio of major to minor radius
- same axis direction
- parallel planes
- arcs that start and run in the same direction
My ellipses have a 2:1 ratio. The panel at the outer end of the bag uses a large ellipse (gentle curve). The panel at the middle seam uses a smaller copy (stronger curve, bigger belly for the bag). The cone between them is one half of one side. I did cut off parts of the ellipses, this is a mistake. To get the cone segment right, I should have used similar pieces of the ellipses, but the error is small enought, so I did not update the design.
The numbers in my model
These are the values in Bag-2.0.FCStd:
| Middle (seam) | Outer end | |
|---|---|---|
| Ellipse major radius | 156.1 mm | 302.5 mm |
| Ellipse minor radius | 78.0 mm | 151.3 mm |
| Ratio | 2 : 1 | 2 : 1 |
| Major axis tilt from vertical | 12.11° | 12.11° |
| Panel height | 260 mm | 300 mm |

The two profile planes are 160 mm apart, so the whole bag is 320 mm wide. The bottle holder is a separate ruled loft between two circles of 50 mm radius, 180 mm apart.
After creating the cone segment, the top and bottom can be cut out to give the bag a nicer shape, like having room for a zipper at the top and a rounded corner at the bottom. This cut does not affect the surface shape of the cone segment, so it stays a developable surface.

FreeCAD workflow
I did the surface work in the Part workbench, then flattened with the Mesh workbench. (My actual FreeCAD model has a twisted plane somewhere, just ignore this).
- Create two ellipse arcs (Part → Primitives → Ellipse) with the same radius ratio and the same angle.
- Place them in parallel planes with identical placement rotation. A flipped Z axis reverses the arc direction and twists the loft.
- Make the panel with Part → Loft, with "Ruled surface" ticked.
- Cut out top and bottom.
- Mirror along yz-plane and xz-plane.

Flattening
To flatten, I adapted the method from MangoJelly Solutions (youtube):
- Select part workbench.
- Select one face, then "Part->Copy->Create Shape Element Copy".
- Select mesh design workbench.
- "Meshes->Mesh from shape"
- "Meshes->unwrap mesh"
Seam allowance in 2D
The flattened outline is the stitching line. The seam allowance is 8 mm on every edge:
- Offset the whole outline outward with Part → 2D Offset, join type "Intersection", by 8 mm.
- Keep the original outline in the pattern as the stitching line.
- The edges with a zipper need some adjustment to have room for the actual zipper. See next section.
Zipper
The main zipper is a waterproof YKK 3C, 317 mm long. I measured the tape at about 24.5 mm wide and the coil at about 4.2 mm. The top panel is modelled as one half with a straight zipper edge, then mirrored for the second half.
At the zipper, the fabric is folded under along the stitching line, so the 8 mm allowance lies on the zipper tape. The two folded edges stop 10 mm apart. That leaves the coil exposed and gives the slider room to run. I worked this out on paper first:

This means that the zipper sides of the pattern have to be 5 mm smaller than they are after adding the 8 mm offset for seam allowance. I did not figure out a nice process to do this. I used Draw and Part workbenches and cut out a rectangle with 5 mm overlap from the 2D-pattern.